Can’t find your vane?We’ll make it to measure.

Custom vacuum pump vanes, even if your equipment is discontinued or nobody knows where it came from. Measure your old vane and we’ll make it in Barcelona.

Don’t have the vane? Take the measurements from the rotor

  • Discontinued equipmentIf the manufacturer no longer makes it, we do
  • No part number or nameplateWe work from your old vane, its dimensions or a drawing
  • Unknown originWe’ve solved those cases too
  • Kits in 43 countriesMade in Barcelona, from 4 units

If the manufacturer no longer makes it, we do. If nobody knows where your equipment came from, we still do.

Your vane isn’t lost.We just need its measurements.

We’ve made vanes for discontinued equipment, for machines with no part number and even for machines of unknown origin, and today they run normally. You don’t need to know the name of the spare part: information about the machine is enough for us to start the assessment.

How to measure your vane with a caliper

  1. Length

    From end to end, with the caliper jaws sitting squarely against both ends.

  2. Width

    From edge to edge, at right angles to the length.

  3. Thickness

    At several points: a worn vane may no longer match its nominal size.

Give the dimensions in millimetres. You must tell us whether the pump is dry-running (oil-free) or oil-lubricated so we can check compatibility. The number of vanes in the rotor also helps.

Don’t have the vane?Measure the rotor.

If the vane has broken, gone missing or you never had it, the rotor slots still hold its dimensions. A caliper is all you need, whether the rotor has a shaft, a hub, or is short with a large diameter.

  1. Slot length

    This is the vane’s length. Measure it from one face of the rotor to the other with the large outside jaws.

  2. Slot width

    This is the vane’s thickness. Insert the small inside jaws and open them until they touch both walls.

  3. Slot depth

    This is the vane’s width. Rest the end of the caliper beside the slot and lower the depth rod to the bottom. If the slot is angled, follow its angle.

  4. Diameter and number of slots

    Measure the rotor diameter and count the slots. If you can, also measure the inside diameter of the cylinder and send us a photo of the rotor.

  5. Your vane, made to measure

    From those dimensions, we make your vane in carbon graphite, G11++ or Kevlar. We check the fit before manufacturing.

The rotor’s dimensions are the reference: with worn rotors or angled slots, we check every dimension with you before manufacturing.

  1. We identify what you need

    Send us the brand, model, previous part number and the dimensions of each vane, if you have them. You can attach photos, a drawing or a sample.

  2. We review the application

    Our team checks dimensions, bevels, material, operating conditions and quantity. See our technical verification criteria.

  3. We prepare your proposal

    We outline feasibility, proposed material, quantity, price and estimated lead time, all subject to technical confirmation.

They’d run out of vanes.Today they’re back to normal.

We’ve made vanes for many machines that had no spare available, and delivered them wherever they were. Those machines are working normally, and many customers have already come back to us for another set of vanes.

  1. No vanesThe manufacturer no longer makes them, or nobody knows the part number.
  2. RunningWe measure, manufacture and deliver them to you. The equipment is back at work.
  3. And they come backMany customers reorder their vane sets from us.
43countries with HARDVANES vane kits
  • 4unitsMinimum manufacturing order
  • 800mmMaximum length in G11++ and Kevlar; up to 400 mm in carbon graphite. Beyond that, ask us.
  • 8mmMaximum thickness in all three materials. Beyond that, ask us.
  • BarcelonaWhere we make and machine your vanes

The making ofyour custom vane.

Every vacuum pump or compressor needs a geometry suited to its rotor and its working conditions. We treat every vane as a technical component.

  1. Material to suit the application

    We select carbon graphite, G11++ fibre or other composites according to the design and lubrication.

  2. Dimensions and tolerances

    We check length, width, thickness, flatness and fit against the original part number, a sample or a drawing.

  3. Bevels, edges and grooves

    We mill profiles, edges and grooves only where the original geometry and the application call for them.

  4. Polishing and surface finish

    We aim for uniform surfaces and a fine polish, up to a mirror finish where technically appropriate.

  5. Edge marking

    As on this G11++ H180554: brand, reference and material engraved on the edge.

    Design yours

Indicative 3D visualisation of the HARDVANES® H180554 G11++ fibre vane, 180 × 55 × 4 mm, with three grooves. Geometry and finish are verified before manufacturing.

More on machining, bevels and finishes

Choosing the right material isn’t enough. The geometry and finish of each vane affect how it fits inside the rotor. We work out the operations needed to reproduce the part’s functional characteristics.

Custom-machined graphite vanes

Carbon graphite vanes for vacuum pumps and compressors are assessed on their dimensions, tolerances and operating conditions. Machining lets us adapt lengths, thicknesses, profiles and edges in compact or large formats, always to each machine’s technical specifications.

Precision grooves and bevels

Technical milling defines transverse grooves, bevels, profiles and the specific details of each vane or blade. We keep to the position and orientation set out in the original design, without adding grooves or changing the geometry for looks. We also check flatness, parallelism and edge finish.

Fine polishing and mirror surfaces

Polishing aims to minimize machining marks and produce even surfaces. Where the composite allows, we consider a high-gloss or mirror finish. Appearance never replaces the requirements for roughness, dimensional accuracy or a vane’s compatibility with its vacuum pump.

Need custom graphite vanes, blades or carbon vanes for a discontinued vacuum pump or an industrial compressor? Send us the model, the dimensions and photos or CAD drawings. HARDVANES® will review the material, geometry and finish before confirming manufacturing feasibility. If you’re looking for a part that’s already available, see our vane catalog by brand; to learn about the material and how to choose it, visit HARDVANES® vane technology.

The materialmakes the difference.

Carbon graphite, G11++ fibre or Kevlar: the design of the vacuum pump or compressor, its lubrication and its working conditions determine the choice.

  • HARDVANES® EKVAC EVO+ carbon graphite vane, 320 × 55 × 6 mm

    Carbon graphite

    For compatible dry-running equipment. Grade and geometry subject to technical review.

    HARDVANES® EKVAC EVO+ · German-origin graphite

    Up to 400 mm long and 8 mm thick

  • G11++ fibre vane with grooves and edge marking

    G11++ technical fibre

    A specific composite for certain lubricated pumps and mechanical requirements.

    Reference H180554 · 180 × 55 × 4 mm

    Up to 800 mm long and 8 mm thick

  • HARDVANES H180554 ESP Kevlar Pharaontex 999 vane, with a smooth face and no grooves

    Kevlar

    Pharaontex 999 composite for compatible vacuum pumps and compressors, subject to technical review.

    Reference H180554 ESP · no grooves

    Up to 800 mm long and 8 mm thick

Technical data

Typical material values, for reference. Compatibility with your equipment is always confirmed in the technical review.

G11++ technical fibreWoven glass fabric and epoxy resin laminate, NEMA G-11 type (IEC 60893 / DIN EN 60893)
Flexural strengthperpendicular to laminations, at 20 °C340 MPa
Flexural modulus24,000 MPa
Tensile strength300 MPa
Compressive strengthperpendicular to laminations350 MPa
Charpy impact strengthparallel to laminations33 kJ/m²
Cleavage strengthparallel to laminations30 MPa
Density1.7–2 g/cm³
Temperature indexby grade: G-11/155, G-11/180 or G-11/220155–220 °C
Water absorption3 mm thick test specimen22 mg
Maximum lengthbeyond that, ask us800 mm
Maximum thicknessbeyond that, ask us8 mm
KevlarPharaontex 999 · Para-aramid (Kevlar®) fabric with high-temperature phenolic resin
DensityASTM D7921.3 g/cm³
Flexural strengthlengthwise / crosswise, ASTM D790139 / 125 MPa
Flexural strengthat 200 °C, lengthwise / crosswise102 / 80 MPa
Tensile strengthlengthwise / crosswise, ASTM D638106 / 73 MPa
Glass transition temperature (Tg)162 °C
Linear thermal expansionin-plane, depending on direction, ASTM E8316.2–12.6 µm/m·°C
Maximum lengthbeyond that, ask us800 mm
Maximum thicknessbeyond that, ask us8 mm
  • Phenolic resins

    Reinforced materials for compatible applications, subject to technical assessment.

  • Special geometries

    We assess other fibres, bevels, grooves and formats to suit the equipment’s needs.

Every geometryhas a purpose.

Four references, six views. Different solutions for your application.

Two graphite formats and two detail views each for G11++ fibre and Kevlar. Views of the same technical material do not necessarily show different geometries. Compatibility and finishes subject to review.

The detailchanges everything.

The decisions that make a part the right replacement for your equipment.

Reference G11++ vane with three grooves

Every groove in its place

Grooves and edges

We check the face, position, orientation and number of grooves. The reference G11++ vane has three grooves and the Kevlar example has none; we don’t assume either configuration for other pumps.

HARDVANES® carbon graphite vane, 320 × 55 × 6 mm, measured for length, width and thickness

Length × width × thickness

Dimensions and wear

We check length, width and thickness at several points. A worn part may no longer match its nominal size, so we compare sample, drawing and manual before setting dimensions and tolerances.

Kevlar vane with an ungrooved face

The choice starts with your equipment

Material and lubrication

We must know whether the pump is dry-running or oil-lubricated. HARDVANES® EKVAC EVO+ carbon graphite, G11++ epoxy fibre and technical materials are assessed against the service conditions.

Thin profile of a Kevlar vane

The details work too

Polishing and finish

We look at milling, fine machining, flatness, parallelism and edge finishing. High-gloss or mirror polishing is considered only when the material and the functional specification allow it.

Minimum manufacturing order: 4 units. Material, dimensions and compatibility subject to technical review.

Made in Spain.Made in Europe.

HARDVANES® carbon graphite vane machined in Barcelona

Machined in Barcelona

We manufacture and machine our custom vanes in Barcelona, and ship them from here to customers in 43 countries. Dimensions, bevels and finishes follow the reference and the conditions of each application.

German carbon graphite

For HARDVANES® EKVAC EVO+, we use German-origin carbon graphite specified for dry-running vacuum pump and compressor vanes.

Explore graphite technology

Frequently asked questionsabout custom vanes.

What customers usually ask us before requesting a quote. You’ll find more answers in our vacuum pump vane FAQ, our vane technology page and our tips for changing vanes. Or send us your dimensions.

What if I can’t find the vane for my vacuum pump?

First, check whether it’s in our vacuum pump vane catalog. If it isn’t, measure your old vane with a caliper (length, width and thickness), tell us whether the pump is dry-running or oil-lubricated and, if you know it, the equipment model. With that information we study the vane and prepare a proposal to make it to measure.

Do you make vanes for discontinued equipment or equipment of unknown origin?

Yes. We’ve made vanes for discontinued equipment, for machines whose manufacturer no longer makes them and for equipment with no part number or nameplate, even of unknown origin. We work from your old vane, its dimensions or a drawing.

What’s the minimum order?

The minimum manufacturing order is 4 units.

Which materials do you use for custom vacuum pump vanes?

Carbon graphite for compatible dry-running equipment, G11++ technical fibre and Kevlar Pharaontex 999. We also assess phenolic resins and other fibres. The material is chosen according to the pump’s design, its lubrication and its working conditions.

Why do I need to say whether the pump runs dry or with oil?

It’s required to verify material compatibility. A vane for a dry-running pump isn’t specified in the same way as one for an oil-lubricated pump.

My vane is worn. Can I still measure it?

Yes. Bear in mind that a worn vane may no longer match its nominal size: measure the thickness at several points and, if you have the original dimension, a drawing or the pump model, let us know. We check it before manufacturing. To know when it’s time to replace it, see how to check vane wear.

I don’t have the vane. Can I give you the rotor dimensions?

Yes. The length of the rotor slot is the vane’s length, the slot width is its thickness and the slot depth is its width. Also measure the rotor diameter, count the slots and tell us whether they’re radial or angled. This works for rotors with a shaft, with a hub, or short large-diameter rotors. We check the fit before manufacturing.

What’s the largest size you can make?

In carbon graphite we make vanes up to 400 mm long and 8 mm thick. In G11++ technical fibre and Kevlar, up to 800 mm long and 8 mm thick. Beyond those sizes, ask us: we look at each case individually.

Do you ship vanes outside Spain?

Yes. We’ve shipped vane kits to customers in 43 countries. Many machines that had run out of vanes are running normally today, and many customers reorder their vane sets.

Where are the vanes made?

We manufacture and machine our custom vanes in Barcelona. For HARDVANES® EKVAC EVO+, we use German-origin carbon graphite.

43 countries. Machines back at work. Customers who come back. Now, your vane.

Your size.Your material. Your vane.

Choose the dimensions, graphite or fibre grade, quantity and finish. We’ll prepare a proposal tailored to your vacuum pump or compressor, as we have for customers in 43 countries.

Don’t know the dimensions or the lubrication? We can start with the model and a photo of the nameplate. We’ll help you identify the spare part.

    01 / DIMENSIONS

    Exact dimensions

    Enter nominal dimensions in millimetres; decimals are accepted. Unsure of the dimensions? Ask us before requesting a quote ↗

    Reference dimensions · editable



    02 / MATERIAL

    Choose your material

    Selection is indicative; our team will check application compatibility.

    Material family

    03 / EQUIPMENT

    Your pump, our reference

    Identify the equipment and attach a photo or drawing if available.


    JPG, PNG, PDF, CAD, DWG, DXF, STEP, STP, IGES, IGS · maximum 3 MB

    04 / CONTACT

    Receive your proposal

    We will contact you to assess feasibility, price and lead time.




    * Required fields are indicated in the form