Skip to content
ContactMy accountCart
EN
Languages 2
Skip to question search
Dry-running rotary vane vacuum pump open on a workbench: steel rotor with six graphite vanes, cover removed and new HARDVANES vanes

Technical help · Vanes for vacuum pumps and compressors

99 questions about vacuum pump vanes

How to identify your vane by brand and reference, what each symptom indicates, which material to choose, how to fit it and how to order custom vanes. Each answer has its own link.

99
technical answers
5
topics, from the nameplate to the order
1 link
direct to each answer

Before you start

This is how a vane works inside the pump.

The rotor rotates off-center inside the cylinder. The vanes slide out of their slots, press against the wall and divide the space into cells that change size with each revolution. Click each phase to see it.

Cross-section of a rotary vane vacuum pump Eccentric rotor with six graphite vanes inside a cylinder. The cells between vanes transition from blue, vacuum at suction, to gold, atmospheric pressure at exhaust.
VacuumAtmospheric pressure

Reduced speed for viewing. In service, approx. 1,450 rpm.

Exploded view of a rotary vane vacuum pump along the axis: cover, bolts, gasket, rotor with vanes and body

Questions 01–21 of 99 · Identify

Identify my vane

Brand, model, reference and compatibility.

Start with your pump nameplate and the spare part reference. In this category, you will find how to identify compatible vanes by brand and model, which data to compare in the data sheet and what to do if the original code is missing. The brands identify the target equipment; check the indicated compatibility for the HARDVANES spare part on each product.

  1. Two sets of graphite vanes with reference labels WN 124-034 and WN 124-161 to identify the spare part for a BECKER pump
    Two sets of graphite vanes with reference labels WN 124-034 and WN 124-161 to identify the spare part for a BECKER pump

    Identify my vane

    How do I identify vanes for BECKER?

    Check the full model and the WN reference. For example, WN 124-034 and WN 124-161 correspond to different references and must not be interchanged.

    Keep all groups of digits and symbols in the WN reference when searching for BECKER vanes. Cross-reference the shop result with the model on the nameplate; do not choose a similar reference just because it shares the first digits.

  2. Pump data sheet, graphite vane and digital calliper showing 45.00 mm to select vanes for ELMO RIETSCHLE
    Pump data sheet, graphite vane and digital calliper showing 45.00 mm to select vanes for ELMO RIETSCHLE

    Identify my vane

    How do I select vanes for ELMO RIETSCHLE?

    Use the exact model, series and spare part code. Confirm the dimensions and application with the corresponding data sheet.

    For ELMO RIETSCHLE vanes, also compare the model suffixes and any version indication appearing in the documentation. If the previous reference is incomplete, send a photograph of the label or the exploded view for review.

  3. Graphite vane for a dry pump next to a laminate vane for an oil-lubricated pump, with drops of oil on it: they are not interchangeable
    Graphite vane for a dry pump next to a laminate vane for an oil-lubricated pump, with drops of oil on it: they are not interchangeable

    Identify my vane

    Are BUSCH vanes for dry and R5 units the same?

    Equivalence between dry and lubricated series should not be assumed. Identify the full model and select only the indicated reference.

    When searching for BUSCH vanes, specify if the equipment is dry-running or lubricated and attach the nameplate. The brand name covers different designs; the selection must reach the specific part reference, not just the family.

  4. Nameplate of a vacuum pump with type, serial number, flow rate and voltage to identify the model
    Nameplate of a vacuum pump with type, serial number, flow rate and voltage to identify the model

    Identify my vane

    How do I identify ORION KRX or KRF vanes?

    Provide the equipment nameplate and its exact code. The series alone may be insufficient to ensure compatibility.

    For an ORION vane inquiry, reproduce letters, numbers and suffixes of the identification exactly. If you have several pumps, separate the data for each; mixing photographs of different nameplates can lead to an incorrect spare part selection.

  5. Vane measured with digital calliper at 45.00 mm over its dimensioned drawing to study DVP, PVR and GEV references
    Vane measured with digital calliper at 45.00 mm over its dimensioned drawing to study DVP, PVR and GEV references

    Identify my vane

    Do you work with DVP, PVR and GEV?

    We can study a reference if we receive the model, dimensions and technical documentation. Each proposal must be validated for the specific equipment.

    Indicate if you need a catalog part or wish to request custom manufacturing for DVP, PVR or GEV. A request may require additional documentation; receipt of data does not equate to confirmation of availability or compatibility.

  6. Long vane for a rotary vane compressor on its technical drawing next to a steel ruler
    Long vane for a rotary vane compressor on its technical drawing next to a steel ruler

    Identify my vane

    Do you offer vanes for MATTEI or HYDROVANE compressors?

    Feasibility depends on the model and design. Send the serial number, original reference and dimensions or drawing to analyze the request.

    For MATTEI or HYDROVANE compressor vanes, add the duty cycle and lubrication information found in the manual. Keep compressor requests separate from vacuum pump vane inquiries.

  7. Pump baseplate with the footprint and holes of a missing nameplate, and a used vane measured with a calliper
    Pump baseplate with the footprint and holes of a missing nameplate, and a used vane measured with a calliper

    Identify my vane

    What do I do if my pump has no nameplate?

    Send clear photos of the equipment and the vane, as well as any available document or reference. A physical sample may be necessary for identification.

    Look for motor labels, maintenance documentation and previous invoices, clearly indicating which component each piece of data belongs to. The motor nameplate can guide the inquiry, but does not necessarily identify the pump model or vane reference.

  8. Micrometer measuring the thickness of a graphite vane next to the pump data sheet
    Micrometer measuring the thickness of a graphite vane next to the pump data sheet

    Identify my vane

    Can you check LEYBOLD Sogevac and Trivac references?

    Yes, we can study the inquiry with the full identification of the equipment and the spare part. Material and geometry compatibility must be verified.

    In a LEYBOLD Sogevac or Trivac request, include the full version and the identification of the requested component. Do not assume that all parts within the same family share the same material, dimensions or substitution possibilities for a compatible alternative.

  9. Organised maintenance kit: six graphite vanes, filter cartridge, O-rings, cover gasket and bolts
    Organised maintenance kit: six graphite vanes, filter cartridge, O-rings, cover gasket and bolts

    Identify my vane

    What does a maintenance kit include?

    The contents depend on the commercial reference. Check specifically whether it includes vanes, filters, gaskets or other items before purchasing.

    Read the kit contents in addition to the commercial title and compare quantities with the planned maintenance. If you need filters or gaskets separately, identify them before purchasing so that the delivery covers the items actually required by the equipment.

  10. Fine graphite vane next to an unbranded porous graphite vane, compared with a magnifying glass
    Fine graphite vane next to an unbranded porous graphite vane, compared with a magnifying glass

    Identify my vane

    How do I compare spare parts from different suppliers?

    Compare reference, material, dimensional precision, finish, scope of supply and technical support. Price alone does not allow compatibility to be assessed.

    Request comparable quotes: same number of units, specification, documentation, and shipping destination. A price difference between vacuum pump vanes may correspond to different supply scopes; reviewing the scope avoids comparing a full set with an individual part.

  11. Equipment parts list with the vane line highlighted and a graphite vane placed on top
    Equipment parts list with the vane line highlighted and a graphite vane placed on top

    Identify my vane

    Can you look into vanes for ATLAS COPCO?

    We can analyze the inquiry if you provide the full model, serial number, and original reference. Compatibility must be validated for the specific equipment.

    For ATLAS COPCO inquiries, distinguish the machine identification from the specific wear part reference. Attach the exploded view when available and explain whether you are looking for a documented replacement or want a special part to be assessed.

  12. Laser engraving on the edge of a vane: HARDVANES ® H100X45X4 ESP, showing height, length, and thickness measurements
    Laser engraving on the edge of a vane: HARDVANES ® H100X45X4 ESP, showing height, length, and thickness measurements

    Identify my vane

    Can you look into vanes for GARDNER DENVER?

    Send the full identification of the equipment and the vane. With these details, we study the material, geometry, and feasibility.

    For GARDNER DENVER, keep any secondary codes appearing on the nameplate or the previous spare part. These details may be necessary to define the version; a match in the trade name is not enough to confirm the part.

  13. Digital calliper measuring a vane at 44.80 mm next to the reference vane to compare dimensions
    Digital calliper measuring a vane at 44.80 mm next to the reference vane to compare dimensions

    Identify my vane

    Do you work with EDWARDS references?

    We can review the request if you provide the exact model and the spare part reference. Equivalence should not be assumed without checking dimensions and application.

    Not all EDWARDS equipment uses the same technology or the same spare part. First, identify the component you need using the parts manual and provide that reference before requesting an alternative or custom manufacture.

  14. Vacuum pump parts list with spare part references and a highlighter pen
    Vacuum pump parts list with spare part references and a highlighter pen

    Identify my vane

    Can you look into vanes for PFEIFFER VACUUM?

    Indicate the full model and the spare part reference. We will assess the request based on the available technical documentation.

    In a PFEIFFER VACUUM inquiry, attach the relevant exploded view page if available. Distinguishing the requested component and its position avoids confusing a vane inquiry with another equipment maintenance item.

  15. Set of four graphite vanes standing up and a digital calliper at 45.00 mm to check the height
    Set of four graphite vanes standing up and a digital calliper at 45.00 mm to check the height

    Identify my vane

    Can you check references for GAST pumps?

    Yes, we can study the inquiry with the model, serial number, and photographs. Compatibility is confirmed after analysing the part.

    To search for GAST vanes, check the full equipment reference and the quantity required per set. If you only have a used part, report its condition and accompany measurements with photographs that allow each dimension to be interpreted.

  16. Nameplate on the equipment base, graphite vane, and digital calliper to identify the spare part
    Nameplate on the equipment base, graphite vane, and digital calliper to identify the spare part

    Identify my vane

    Do you offer vanes for KAESER equipment?

    Feasibility depends on the model and design. Send the nameplate, original reference, and measurements to analyze the request.

    When enquiring about KAESER, specify the machine type and the specific component requested. Not every compressor brand uses a single design; the supply proposal must be supported by an identified reference and sufficient documentation.

  17. Rotor removed from the pump, resting on blocks with its vanes: the bottom ones protrude from the slots under their own weight
    Rotor removed from the pump, resting on blocks with its vanes: the bottom ones protrude from the slots under their own weight

    Identify my vane

    Can you look into vanes for INGERSOLL RAND?

    Provide the model, series, and previous reference. We will check the geometry and material before proposing a solution.

    For INGERSOLL RAND, add any identification of the assembly where the part is mounted and keep the previous order reference. This information helps distinguish spares for different equipment within the same industrial installation.

  18. Technical data sheet, graphite vane, and label with the original reference for cross-referencing
    Technical data sheet, graphite vane, and label with the original reference for cross-referencing

    Identify my vane

    Can you check TUTHILL or KINNEY references?

    We can study the request with the full identification of the equipment and the part. Each proposal must be validated for the specific machine.

    In TUTHILL or KINNEY inquiries, clarify if the documentation identifies the complete pump or a sub-assembly. Attach the available drawing or exploded view to study the correct part without assuming compatibility based solely on the brand.

  19. Old worn vane next to a new custom vane manufactured according to its dimensioned drawing
    Old worn vane next to a new custom vane manufactured according to its dimensioned drawing

    Identify my vane

    What do I do if my vane reference is discontinued?

    Send the sample or drawing and the equipment data. We can assess custom manufacturing based on that information.

    A discontinued reference does not automatically allow for the reconstruction of all original dimensions. Indicate which measurements come from documentation and which from a worn sample; this distinction helps evaluate custom vane manufacturing with clear criteria.

  20. Exploded view of a rotary vane vacuum pump along the axis: cover, bolts, gasket, rotor with vanes and body
    Exploded view of a rotary vane vacuum pump along the axis: cover, bolts, gasket, rotor with vanes and body

    Identify my vane

    How do I locate the vane reference in the equipment's exploded view?

    Consult the parts manual for the exact model and look for the rotor or vane assembly. If you cannot find it, send us the model and we will review it.

    Note the position number and the exploded view revision alongside the manufacturer's reference. Check that the document corresponds to your equipment version; a parts list from a similar series may contain different spares.

  21. Three graphite vanes of different sizes and a digital calliper at 38.00 mm: each pump model takes its own size
    Three graphite vanes of different sizes and a digital calliper at 38.00 mm: each pump model takes its own size

    Identify my vane

    Does the same vane work for several models of a brand?

    It should not be assumed. Compare reference, dimensions, and material for each model; a partial match does not guarantee compatibility.

    When managing several models, create a correspondence between each pump and its confirmed vane reference. Only group orders if the documentation allows it: sharing a brand, appearance, or approximate dimensions does not prove the spare is interchangeable.

Three HARDVANES carbon graphite vanes with the reference H100X45X4 engraved on the edge, in front of an open vacuum pump

Vanes HARDVANES

The reference, engraved on the edge.

Each vane has the brand, measurements, and origin engraved on the edge. This allows the spare to be identified with the part in hand, without depending on the box or the delivery note.

  • EKVAC EVO+ carbon graphiteMaterial made specifically for vacuum and compression
  • Material from GermanyMachined, milled, and polished in Spain
  • Compatibility by referenceVerified for each geometry and working condition
Thermal image of a rotary vane vacuum pump: the pump body is the hottest area and the motor remains cooler

Questions 22–41 of 99 · Troubleshooting

Solve a problem

Loss of vacuum, noise, heat, breakages, or wear.

If your pump loses vacuum, makes noise, or wears out vanes sooner than expected, first identify the symptom and its conditions. These answers help you prepare information for an inspection and distinguish a need for spares from other problems in the assembly. The purchase must be supported by the verified reference and the corresponding diagnosis.

  1. Graphite vane broken into three pieces with a jagged fracture and graphite crumbs on the bench, in front of an open vacuum pump
    Graphite vane broken into three pieces with a jagged fracture and graphite crumbs on the bench, in front of an open vacuum pump

    Solve a problem

    Why does a vane break prematurely?

    Causes can include incorrect assembly, contamination, mechanical wear, obstructions, or improper selection. Stop the equipment and check the assembly before installing new parts.

    Keep the fragments and photograph their location if it can be done safely. Note the hours since the last change, the material installed, and the condition of the filters; these data help study repeated vane breakage.

  2. Interior of an open vane pump: one of the vanes is not touching the cylinder wall
    Interior of an open vane pump: one of the vanes is not touching the cylinder wall

    Solve a problem

    What does a chattering noise indicate?

    An unusual noise may indicate contact, wear, or operational problems. Interrupt service and request a technical inspection following the equipment procedure.

    Describe if the chattering appears at start-up, when hot, or throughout the cycle. A record of the incident helps the technician narrow down the problem, but a sound recording alone does not confirm which spare to buy.

  3. Thermal image of a rotary vane vacuum pump: the pump body is the hottest area and the motor remains cooler
    Thermal image of a rotary vane vacuum pump: the pump body is the hottest area and the motor remains cooler

    Solve a problem

    Why is the pump overheating?

    Ventilation, filters, service duty, and mechanical condition must be checked according to the manual. If the normal range is exceeded, stop the equipment safely.

    Note if the heating started after changing filters, installing vanes, or modifying the process. Compare equivalent working conditions; replacing only the vanes does not resolve a ventilation restriction or an out-of-specification operating condition.

  4. Exhaust silencer outlet of a dry vacuum pump with soot and graphite dust grains
    Exhaust silencer outlet of a dry vacuum pump with soot and graphite dust grains

    Solve a problem

    Is it normal to find graphite dust in the exhaust?

    Some particle generation may be associated with wear in dry applications. An abnormal increase requires checking the vanes, filtration, and operating conditions.

    Monitor how it changes compared to normal operation and record the hours of the installed set. The presence of dust, on its own, does not identify an incorrect graphite grade; the assessment must consider quantity, wear, and actual service conditions.

  5. Graphite vane on sandpaper with graphite dust: modifying a vane by hand alters its dimensions
    Graphite vane on sandpaper with graphite dust: modifying a vane by hand alters its dimensions

    Solve a problem

    Can I sand a vane to adjust it?

    Do not modify dimensions or bevels by hand without an approved procedure. Incorrect adjustment can alter clearances and cause damage to the equipment.

    Thickness, flatness, and bevels are part of the functional specification of the spare part. If a new vane does not fit, first compare the reference and dimensions; request a review before altering a part that might not correspond to the model.

  6. Removed rotor with vanes stuck at different heights in their slots and traces of residue
    Removed rotor with vanes stuck at different heights in their slots and traces of residue

    Solve a problem

    What should I do if the vanes get stuck?

    Stop the equipment and have trained personnel check for dirt, contamination, slots, and the condition of the parts. Use only the recommended cleaning process.

    Indicate if the sticking appeared after a period of downtime, cleaning, or a material change. This sequence is relevant for the inspection. Do not use the purchase of a new set as a substitute for checking the rotor slots.

  7. New vane next to a vane with wedge wear: resting on a ruler by the base, the worn one leaves a triangular gap against the front ruler
    New vane next to a vane with wedge wear: resting on a ruler by the base, the worn one leaves a triangular gap against the front ruler

    Solve a problem

    What causes uneven wedge-shaped wear?

    This may be related to geometry, assembly, or equipment condition. Record photographs, working hours, and dimensions to guide the inspection without assuming a single cause.

    Compare parts from the same set and note which faces show the most wear. A photograph of each vane, identified by its position if known, provides more information than a single general image of the disassembled set on the bench.

  8. New ball bearing next to a worn bearing on the workbench
    New ball bearing next to a worn bearing on the workbench

    Solve a problem

    When should bearings be replaced?

    The frequency depends on each model and the inspection results. It should not be deduced solely from the number of vane sets consumed.

    Include the history of vibrations, noise, and repairs in the bearing review. Vacuum pump maintenance must assess the condition of the entire assembly; repeatedly replacing vanes does not correct a pending mechanical problem.

  9. Rotor with vanes mounted and the rotation direction arrow engraved on the rotor face
    Rotor with vanes mounted and the rotation direction arrow engraved on the rotor face

    Solve a problem

    What happens if I fit the bevel backwards?

    The mounting orientation is functional and must be respected. Check the correct direction in the manual before starting the equipment.

    Before removing old parts, document their position whenever the procedure allows. If that installation was also doubtful, do not take it as a valid reference: cross-check it with the manual or the technical documentation of the equipment.

  10. Set of six vanes standing: five worn and one new, taller than the others
    Set of six vanes standing: five worn and one new, taller than the others

    Solve a problem

    Can I replace a single vane from the set?

    Follow the manufacturer's instructions regarding the replacement of the complete set. Mixing new and used parts can lead to differences in wear or performance.

    When buying spare parts, verify how many units the sales reference contains and how many your rotor needs. The term "vane set" must correspond to specific contents; confirm the quantity to plan the job without missing parts.

  11. Vacuum gauge in bar with the needle at −0.48 bar in front of a vane pump
    Vacuum gauge in bar with the needle at −0.48 bar in front of a vane pump

    Solve a problem

    Why is the pump's ultimate vacuum dropping?

    This may be due to wear, leaks, clogged filters, or contamination. Review the assembly following the manual before deciding which parts to replace.

    Indicate where the vacuum is measured, with which instrument, and under what conditions. A reading at the process and another at the pump can describe different situations; comparing equivalent measurements helps decide if the vanes should be inspected.

    With new vanes fitted, the pump works at 100% of its performance again. With the cylinder, rotor and the rest of the pump in good condition.

  12. Dirty suction filter cartridge next to a new cartridge
    Dirty suction filter cartridge next to a new cartridge

    Solve a problem

    Why is the flow rate lower than expected?

    Possible causes include worn vanes, excessive clearances, or suction restrictions. A diagnosis requires measuring and comparing with the equipment specifications.

    Distinguish a reduction in flow from a loss of ultimate vacuum: these are different observations. Record the process behavior and measurement conditions so that the inspection is not limited to replacing spares without a prior diagnosis.

  13. Analogue panel ammeter with the needle in the red zone of the scale
    Analogue panel ammeter with the needle in the red zone of the scale

    Solve a problem

    What does high power consumption indicate?

    This may indicate excessive friction, obstructions, or an out-of-range service condition. Stop the equipment and request a qualified inspection.

    Note the observed values and the conditions under which they appeared, leaving electrical checks to qualified personnel. High consumption does not automatically identify a defective vane; it must be studied alongside the load, mechanical state, and installation.

  14. Cracked rubber anti-vibration mount under the base of a vacuum pump, with a loosened nut beside it
    Cracked rubber anti-vibration mount under the base of a vacuum pump, with a loosened nut beside it

    Solve a problem

    What do abnormal vibrations mean?

    These may be related to bearings, misalignment, or parts in poor condition. Do not continue operating the equipment until the source is identified.

    Note if the vibration appeared after a relocation, a repair, or a change in the process. Keep this chronology for the technical review. Buying a new set of vanes is no substitute for checking supports, alignment, and components.

  15. Puddle and streaks of oil under the body of a vacuum pump
    Puddle and streaks of oil under the body of a vacuum pump

    Solve a problem

    Why are there oil leaks in a lubricated pump?

    These may come from deteriorated gaskets, seals, or connections. Identify the exact point and replace the elements using the manufacturer's references.

    Before ordering gaskets or seals, identify the leak area and the pump version. Do not attribute an external oil leak to the vanes without a review: the necessary spare part may belong to another assembly.

  16. Two vanes standing seen from the end: the new one with a sharp edge tip and the worn one with a rounded, lower tip
    Two vanes standing seen from the end: the new one with a sharp edge tip and the worn one with a rounded, lower tip

    Solve a problem

    What does excessive wear on the edge of the vane indicate?

    This may be associated with contamination, misalignment, or severe working conditions. Keep the part and record photographs to analyze the cause.

    Photograph the affected edge along with the other faces of the part and, if known, its mounting position. Comparing all vanes in the set helps document whether the observed wear is uniform or localised.

  17. Interior of a vane pump cylinder with circumferential score marks and a graphite film on the wall
    Interior of a vane pump cylinder with circumferential score marks and a graphite film on the wall

    Solve a problem

    Why do score marks appear in the chamber?

    These can be produced by particles, unsuitable materials, or abnormal contact. If the chamber is damaged, evaluate its condition before fitting new vanes.

    A scratched surface can affect the operation of new parts. Keep images of the damage and avoid hiding it with improvised touch-ups; the decision to repair or replace components must be based on the technical criteria of the model.

  18. Rotor with vanes retracted in their slots and traces of residue preventing them from coming out
    Rotor with vanes retracted in their slots and traces of residue preventing them from coming out

    Solve a problem

    Why do vanes jam during start-up?

    Dirt, residues, moisture, or incorrect assembly can be factors. Do not force the start-up; check the stopped equipment according to the manual.

    Note how long the equipment was stopped and what storage or process conditions preceded the jam. This background helps guide the inspection without assuming that every start-up difficulty stems from the material of the installed vanes.

  19. Graphite vane with chipped edges and splinters on the bench
    Graphite vane with chipped edges and splinters on the bench

    Solve a problem

    What does chipping on the edges indicate?

    This may be due to knocks, improper assembly, internal impacts, or an unsuitable grade. Replace the damaged part and check the source of the problem.

    If you detect chipping before assembly, set the part aside and check the packaging. If it appears after service, record the hours and working conditions; differentiating between these two moments helps investigate handling, transport, or operation.

  20. Removed rotor on V-blocks next to a digital calliper for measuring its slots
    Removed rotor on V-blocks next to a digital calliper for measuring its slots

    Solve a problem

    When is it advisable to check the rotor in addition to the vanes?

    When slots or surfaces show wear, damage, or abnormal clearances. Measure and compare with the manufacturer's limits before fitting new parts.

    Inspecting the rotor makes it possible to check the slots that house the vanes, not just the consumable spare. If damage exists, keep the measurements and photographs to assess the assembly before ordering new parts of the same reference.

Set of carbon graphite vanes stacked with the engraving HARDVANES ® H100X45X4 ESP on the edge

Questions 42–61 of 99 · Materials

Choose the material

Carbon graphite, epoxy fibre, and working conditions.

Choose the material based on the equipment specification, not just the part size. Carbon graphite, epoxy fibre, surface finish, tolerances, and service conditions are explained here. For custom vanes, gather the drawing, dimensions, and process data: these allow the material and machining proposal to be assessed before manufacturing.

  1. Sawn graphite block, cut sheet and ground vane: the vane is machined from a block of material
    Sawn graphite block, cut sheet and ground vane: the vane is machined from a block of material

    Choose the material

    What is isostatic graphite?

    It is a material obtained through a compaction process that can promote uniform properties. Its suitability depends on the specific formulation and the requirements of each machine.

    The graphite manufacturing method alone does not identify a vane suitable for your pump. Request the material grade and intended application, especially if you are comparing similar-looking parts from different catalogs.

  2. Carbon graphite vane next to an epoxy fibre vane with the laminate layers visible on the edge
    Carbon graphite vane next to an epoxy fibre vane with the laminate layers visible on the edge

    Choose the material

    Which should I choose: epoxy fibre or carbon graphite?

    The decision depends on the equipment design, dry or lubricated operation, temperature, load and the intended reference. It is not correct to swap materials just because the dimensions match.

    Before choosing between graphite vanes and epoxy fibre vanes, identify the material specified for that reference. Also document the fluid handled and the service duty; changing material family requires a specific technical assessment.

  3. Contact thermometer with magnetic probe on a vacuum pump cover reading 71.8 °C
    Contact thermometer with magnetic probe on a vacuum pump cover reading 71.8 °C

    Choose the material

    What thermal limits can the vanes withstand?

    There is no single limit for all vanes. Each formulation and construction has its permissible range; furthermore, the equipment manufacturer's thermal conditions must be respected.

    Distinguish between ambient temperature, gas temperature and component temperature: these are not equivalent data. Provide the usual working conditions and the maximums observed, without automatically transferring a material limit to the entire pump.

  4. Graphite vane on its edge on a ground steel plate, showing the graphite film it leaves when sliding
    Graphite vane on its edge on a ground steel plate, showing the graphite film it leaves when sliding

    Choose the material

    What does self-lubrication mean?

    Certain carbonaceous materials allow for operation in chambers designed for dry running. This does not mean an absence of wear, nor does it authorise dispensing with maintenance.

    In a dry pump, the carbon graphite selection must correspond to that friction function. The term self-lubricating does not turn a grade intended for electrical brushes or other uses into a valid spare part for a vacuum chamber.

  5. Brown textolite vane next to a graphite vane and a sample label with the original reference
    Brown textolite vane next to a graphite vane and a sample label with the original reference

    Choose the material

    Can I replace a textolite vane?

    Only after checking chemical, dimensional and mechanical compatibility. The brown color is not enough to identify the composition or justify a replacement.

    An aged part can change appearance, so visual identification has limits. If you are looking to replace textolite vanes, provide the original reference or a sample along with the equipment's operation and lubrication information.

  6. 0.01 mm dial indicator measuring a graphite vane on a granite surface plate
    0.01 mm dial indicator measuring a graphite vane on a granite surface plate

    Choose the material

    What tolerances are they manufactured to?

    Tolerances are defined according to the drawing, reference and application. For custom vanes, critical dimensions, bevels, functional surfaces and inspection criteria must be agreed upon.

    When requesting custom vanes, express all dimensions in a clear unit and distinguish nominal dimensions from measurements taken from a worn part. Include slots, radii and bevels in the drawing to leave no room for interpretation during machining.

  7. Graphite vanes in a self-sealing bag with a silica gel desiccant sachet
    Graphite vanes in a self-sealing bag with a silica gel desiccant sachet

    Choose the material

    Does humidity affect the vanes?

    Storage and environmental exposure can have an influence depending on the material. Keep parts dry, clean and protected, following the specific instructions on the packaging.

    If the box arrives damp or has been stored in an unsuitable place, document its condition before assembly. Do not attempt to correct the part by heating or improvised treatments; consult the instructions applicable to that material and reference.

  8. Shore D durometer resting on a graphite vane in its test stand
    Shore D durometer resting on a graphite vane in its test stand

    Choose the material

    Can the hardness be customized?

    Hardness must be evaluated alongside the set of material properties and tribological conditions. A change requires application validation and should not be decided in isolation.

    A harder vane is not automatically a better vane for every pump. The decision must consider contact with the chamber, the strength and wear of the assembly, avoiding the optimisation of a single property at the expense of others.

  9. Graphite vane and ground steel vane on the part drawing
    Graphite vane and ground steel vane on the part drawing

    Choose the material

    Do you manufacture metal vanes?

    The vane composition must correspond to the compressor or pump design. For special solutions, send the reference and the drawing; do not replace graphite with metal without validation.

    Before ordering a special part, clarify whether you are looking to reproduce an existing reference or modify the design. The manufacture of a geometry does not imply that any proposed material will be suitable for the equipment where it will finally be installed.

  10. Rotor with its vanes on blocks and a set of feeler gauges fanned out
    Rotor with its vanes on blocks and a set of feeler gauges fanned out

    Choose the material

    How is the thermal clearance determined?

    It is calculated based on the design, expansion coefficients and operating regime. The tolerances and procedure specified by the manufacturer must always prevail.

    Do not adjust a vane until it appears to fit well when cold: this check does not prove that the operating clearance is correct. Maintain the drawing dimensions and consult the specific measurement procedure for the machine.

  11. Set of carbon graphite vanes stacked with the engraving HARDVANES ® H100X45X4 ESP on the edge
    Set of carbon graphite vanes stacked with the engraving HARDVANES ® H100X45X4 ESP on the edge

    Choose the material

    What is carbon graphite?

    It is a carbonaceous material used in vanes for dry-running chambers. Its properties vary according to the formulation, so the appropriate grade for each piece of equipment must be selected.

    For vacuum pump vanes, a formulation designed for the contact conditions of that application is required. It is not enough for the material to be black or sold as graphite: consult the specification associated with the reference.

  12. Edge of an epoxy fibre vane seen up close: layers of fabric and resin
    Edge of an epoxy fibre vane seen up close: layers of fabric and resin

    Choose the material

    What is epoxy fibre in a vane?

    It is a composite material made of fibre with an epoxy resin matrix. Its behavior depends on the construction and the application; it is not interchangeable with graphite without validation.

    To compare epoxy fibre vanes, request the specified grade and construction in addition to the dimensions. A generic name like laminate does not describe all its properties nor confirm it can replace the part intended for your machine.

  13. Two vanes on their material data sheets A and B: the trade name is not enough, the data sheet must be compared
    Two vanes on their material data sheets A and B: the trade name is not enough, the data sheet must be compared

    Choose the material

    What is the difference between graphite and carbon graphite?

    The trade name can vary between manufacturers and grades. Confirm the composition and technical data sheet for each reference instead of relying solely on the name.

    Use the trade name as a starting point, not as the sole purchasing criterion. The material data sheet and the vane reference allow for a more precise comparison of proposals than broad terms like technical graphite or industrial carbon.

  14. Graphite vane on a precision balance reading 31.52 g, with a calliper next to it to calculate the volume
    Graphite vane on a precision balance reading 31.52 g, with a calliper next to it to calculate the volume

    Choose the material

    Why does material density matter?

    Density and internal structure influence mechanical strength and wear behavior. It must be evaluated alongside the other material properties.

    A density value on its own does not make it possible to predict the service life of an installed vane. If you are comparing data sheets, check that the data corresponds to the grade offered and that the intended application matches that of your pump.

  15. Fracture surface of a graphite vane seen up close, with its grain and crumbs on the bench
    Fracture surface of a graphite vane seen up close, with its grain and crumbs on the bench

    Choose the material

    What is porosity and how does it affect operation?

    It is the presence of microscopic voids in the material. It can influence strength and interaction with the environment, depending on the grade and application.

    Do not infer porosity from a photograph or how the surface feels. For a material inquiry, provide the available technical data sheet and the working conditions prompting the change or selection.

  16. Unimpregnated graphite vane next to an impregnated vane, with labels identifying them
    Unimpregnated graphite vane next to an impregnated vane, with labels identifying them

    Choose the material

    Can graphite be impregnated?

    There are grades treated to modify certain properties. Suitability depends on the equipment and the working fluid; consult before choosing a variant.

    A treatment can modify the material's behavior, so an impregnated grade should not be considered equivalent by default. Identify the approved reference and consult before introducing variants into a dry or lubricated vacuum pump.

  17. Amber bottle with a process sample, safety data sheet and graphite vane
    Amber bottle with a process sample, safety data sheet and graphite vane

    Choose the material

    Are the vanes resistant to chemicals and vapours?

    It depends on the material and the substance. Tell us the working fluid and conditions to assess compatibility before recommending a grade.

    Provide the product name, its known composition and the process conditions, not just the industrial sector. Two applications called "packaging" may draw in different substances; this information is relevant when assessing the selection of the spare part.

  18. Roughness tester measuring a graphite vane: the screen shows Ra 0.38 µm and Rz 2.6 µm
    Roughness tester measuring a graphite vane: the screen shows Ra 0.38 µm and Rz 2.6 µm

    Choose the material

    Does the surface finish influence performance?

    Yes, the functional surfaces and edges determine the contact with the chamber. That is why they are agreed upon in the drawing along with the tolerances.

    Milling, machining and polishing must correspond to the surfaces and dimensions defined for the part. A mirror-like appearance is no substitute for dimensional verification, even if the surface finish is part of the agreed manufacturing criteria.

  19. Graphite vane on a steel ramp with a digital inclinometer at 11.3°: the angle at which it slides shows the friction
    Graphite vane on a steel ramp with a digital inclinometer at 11.3°: the angle at which it slides shows the friction

    Choose the material

    What role does friction play in material selection?

    It affects wear, heating and the stress on the equipment. It must be assessed alongside the load, speed and duty cycle of the machine.

    Explain if you are looking to resolve abnormal wear, temperature or consumption before requesting an alternative material. Changing the vane without knowing the contact conditions may leave the problem that originated the maintenance inquiry unresolved.

  20. Rotor with a set of graphite vanes in which one vane is of another material, brown
    Rotor with a set of graphite vanes in which one vane is of another material, brown

    Choose the material

    Can vanes of different materials be mixed in the same set?

    It is not recommended unless indicated by the equipment manufacturer. Different materials can wear and behave differently.

    Keep each set identified and avoid completing a set with parts of unknown origin. When comparing spare parts, confirm that all units supplied share the intended specification for the rotor and the conditions of the equipment where they will be fitted.

Tools for fitting vanes arranged on a mat: torque wrench, Allen keys, calliper, micrometer, feeler gauges and a set of vanes

Questions 62–81 of 99 · Fitting

Fit and maintain

Installation, cleaning, clearances and maintenance.

A correctly identified purchase must be accompanied by fitting and maintenance in accordance with the model. Find out how to prepare the job, record wear, store spare parts and verify associated elements. The manufacturer's specific instructions and qualified personnel remain the reference for working on the machine.

  1. Open vane pump with a clean cylinder and a lint-free cloth on the bench
    Open vane pump with a clean cylinder and a lint-free cloth on the bench

    Fit and maintain

    How should surfaces be cleaned?

    Use the products and follow the procedures authorised by the manufacturer. Avoid introducing particles, moisture or residues into the chamber and check its condition before closing.

    Cleaning must allow for the inspection of surfaces without hiding damage under residues. Also check the conditions of the assembly area and the temporary storage of parts to avoid reintroducing contamination during pump maintenance.

  2. Tools for fitting vanes arranged on a mat: torque wrench, Allen keys, calliper, micrometer, feeler gauges and a set of vanes
    Tools for fitting vanes arranged on a mat: torque wrench, Allen keys, calliper, micrometer, feeler gauges and a set of vanes

    Fit and maintain

    What tools do I need for fitting?

    Consult the model manual: suitable dismantling, measurement and inspection tools are usually required. Isolate energy sources beforehand.

    Prepare the manual reference, the appropriate instruments and the planned spare parts before starting work. Having the set of vanes does not mean having all the elements necessary to correctly dismantle, inspect and close that model.

  3. Assembled vacuum pump and commissioning log sheet with vacuum, temperature and current
    Assembled vacuum pump and commissioning log sheet with vacuum, temperature and current

    Fit and maintain

    Do new vanes need running-in?

    Some equipment requires specific commissioning. Follow the manufacturer's sequence and avoid applying generic instructions to different models.

    Record the initial checks required by the manufacturer and keep the results in the history. Commissioning allows a reference to be established for subsequent monitoring, without attributing a performance to the vanes that has not been measured.

  4. Dry vane pump open with the label "dry chamber, do not add oil" and an oil can set aside
    Dry vane pump open with the label "dry chamber, do not add oil" and an oil can set aside

    Fit and maintain

    Should I use lubricant when installing the vanes?

    In chambers designed to work dry, do not add oil on your own initiative. Distinguish the pumping chamber from the points that do require lubrication according to the manual.

    Do not confuse a dry vacuum pump with an oil-lubricated pump. Before choosing maintenance products, identify the chamber and the points indicated by the manufacturer; a recommendation for another series may not be applicable.

  5. Direction of rotation arrow on the cover of a vane vacuum pump
    Direction of rotation arrow on the cover of a vane vacuum pump

    Fit and maintain

    How do I verify the direction of rotation?

    Carry out the check according to the manual and with the equipment in a safe condition. This task must be left to qualified personnel.

    Check the rotation marking and the verification procedure for the exact model, especially after electrical work. A similar external appearance between motors or pumps does not allow commissioning instructions to be transferred without reviewing the corresponding documentation.

  6. New O-ring next to an old, flattened and hardened seal, with a seal pick
    New O-ring next to an old, flattened and hardened seal, with a seal pick

    Fit and maintain

    When are O-rings replaced?

    Examine the condition of the sealing elements and apply the instructions from the kit or the manufacturer. Always use the correct dimensions and materials.

    During scheduled maintenance, check which seals the dismantling procedure requires and whether they are included in the kit. Ordering them together with the vanes can help organise maintenance, always with verified references and materials.

  7. Digital calliper measuring a worn vane at 41.20 mm next to a new vane and a limit label according to the manual
    Digital calliper measuring a worn vane at 41.20 mm next to a new vane and a limit label according to the manual

    Fit and maintain

    How do I know if a vane has reached the end of its service life?

    Compare its actual dimensions and condition with the wear limit established for the model. Also check for cracks, breakages and irregular wear.

    The replacement criterion is not solely that the pump continues to work. Save the measurements from each service and compare them with the model limit; this way you can justify the purchase of the next set before reaching unacceptable wear.

    With new vanes fitted, the pump works at 100% of its performance again. With the cylinder, rotor and the rest of the pump in good condition.

  8. Vacuum cleaner nozzle removing graphite dust from the bottom of the cylinder of an open pump
    Vacuum cleaner nozzle removing graphite dust from the bottom of the cylinder of an open pump

    Fit and maintain

    How do I remove graphite residues?

    Use the method and protection indicated by the manual, avoiding the dispersal of dust. Do not use a cleaning technique that could damage surfaces or components.

    Manage waste without contaminating the new vanes or the assembly site. If the pump worked with process substances, inform the maintenance manager: the residues may not be solely graphite and may require a specific evaluation.

  9. Maintenance log for a vacuum pump with dates, hours, operations and minimum vane height
    Maintenance log for a vacuum pump with dates, hours, operations and minimum vane height

    Fit and maintain

    How do I plan preventive maintenance?

    Record working hours, inspections, filter changes and measurements. Adjust services to the application and the manufacturer's recommendations.

    Create a log for each piece of equipment with model, serial number, vane reference and date of last service. An individual history avoids confusing spare parts for similar machines and makes it easier to organise purchases according to the planned maintenance of each pump.

  10. Vacuum pump cover separated and crooked relative to the body: it does not close and must not be forced
    Vacuum pump cover separated and crooked relative to the body: it does not close and must not be forced

    Fit and maintain

    What do I do if the cover does not close?

    Do not force it closed. Verify assembly, reference, cleanliness and position of the parts with the equipment stopped; if the problem persists, request an inspection.

    Resistance to closing is a signal to stop the operation and verify, not to increase the force applied. Document the fitted reference and any dimensional difference compared to the specification before requesting assistance or a different spare part.

  11. Rotor slots of a vane pump illuminated with a torch for inspection
    Rotor slots of a vane pump illuminated with a torch for inspection

    Fit and maintain

    How do I inspect the rotor slots?

    Check cleanliness, wear and the absence of visible damage. Compare the measurements with those of the manufacturer before installing the vanes.

    Identify and record any damage separately to avoid losing its location during disassembly. Do not remove material from the slots as a makeshift adjustment; modifying the rotor can alter the conditions for which the vane was selected.

  12. Digital calliper measuring a vane length, 99.50 mm, over its dimensioned sketch
    Digital calliper measuring a vane length, 99.50 mm, over its dimensioned sketch

    Fit and maintain

    How are vanes measured before fitting?

    With suitable measuring instruments and by comparing with the reference dimension or the model's wear limit. Record the values in your maintenance log.

    Measure length, height and thickness without confusing the order used by each supplier. Add a sketch with the position of each dimension and indicate whether the measurements correspond to a new vane, a used one or a nominal drawing.

  13. Three black HARDVANES boxes with gold logo, labelled with size, equipment and date of receipt, with no weight on top
    Three black HARDVANES boxes with gold logo, labelled with size, equipment and date of receipt, with no weight on top

    Fit and maintain

    How should I store spare vanes?

    Dry, clean, protected from impacts and in their original packaging until the moment of assembly. Avoid stacking weight on top of them.

    Label spares with model, reference and date of receipt to avoid mix-ups in the warehouse. Keeping each set separate makes it easier to locate the correct vanes during a shutdown and preserves supply traceability information.

  14. Graphite vanes standing in a foam tray with slots that protect the edges
    Graphite vanes standing in a foam tray with slots that protect the edges

    Fit and maintain

    How do I handle vanes without damaging the edges?

    Do it carefully and without dropping them or hitting them with tools. The edges and bevels are sensitive functional areas.

    Prepare a clean, stable surface to support the parts and avoid contact with other loose spares. Check the edges before assembly: an impact occurring during handling should not be confused later with operational wear.

  15. Protective mask with valve next to the safety data sheet and graphite dust on the bench
    Protective mask with valve next to the safety data sheet and graphite dust on the bench

    Fit and maintain

    What personal protection should be used with graphite dust?

    Follow your company's and the manufacturer's safety instructions. Use appropriate protection and avoid dispersing dust into the environment.

    Consult the safety documentation for the material and the process where the pump operated. The selection of protection and cleaning depends on the workstation assessment; a generic recommendation does not replace the measures established by the health and safety officer.

  16. Used suction filter, new filter and set of new vanes in front of the pump
    Used suction filter, new filter and set of new vanes in front of the pump

    Fit and maintain

    Should filters be changed when replacing vanes?

    It is a good opportunity to check them. Follow the manufacturer's maintenance plan and replace any that show dirt or wear.

    Check the filters corresponding to the model and its function separately. Vane replacement may coincide with other tasks, but not all kits include filtration; check each product sheet before completing the purchase.

  17. Panel hour meter reading 12,486.3 h next to an ammeter and the maintenance log
    Panel hour meter reading 12,486.3 h next to an ammeter and the maintenance log

    Fit and maintain

    How do I record the service hours of the vanes?

    Note the assembly date, equipment hours, reference and batch of the parts. This history helps plan replacements and analyze incidents.

    Add wear measurements and observed incidents to that record, maintaining one log per pump. With several similar units, this separation helps in purchasing the correct reference and interpreting differences in service life.

  18. Feeler gauge inserted between the rotor and the cylinder of an open vane pump
    Feeler gauge inserted between the rotor and the cylinder of an open vane pump

    Fit and maintain

    How do I check the rotor clearance?

    Measure it following the manufacturer's procedure and values. This operation must be carried out by qualified personnel with the appropriate tools.

    Distinguish the rotor clearance from the vane dimensions and avoid using a single data point to assess the entire assembly. If reference values are missing, request the technical documentation before deciding which part should be changed.

  19. Pre-start checklist and torque wrench next to the assembled pump
    Pre-start checklist and torque wrench next to the assembled pump

    Fit and maintain

    What should I check before the first start-up after fitting?

    Check part orientation, cleanliness, closure, connections and direction of rotation according to the manual. Start only when everything has been verified.

    Complete documentary verifications of the spare in addition to mechanical checks: reference, quantity and material. Keep the assembly and commissioning record to link any subsequent incident with the conditions under which the work was carried out.

  20. Used and broken vanes inside a sealed bag with a waste label
    Used and broken vanes inside a sealed bag with a waste label

    Fit and maintain

    How do I dispose of used vanes?

    Manage them in accordance with local regulations and your company's procedures. Avoid dispersing dust during removal and transport.

    Identify waste according to the actual use of the equipment and the substances it may have come into contact with. Keep parts contained during transfer and consult the waste management procedure applicable to your facility or workshop.

Graphite sheet held in a vice under a carbide milling cutter, with graphite chips

Questions 82–99 of 99 · Orders

Buy or order custom-made

Quotes, manufacturing, shipping and orders.

If you already know the spare part, check the scope of supply in the shop. For custom vanes, provide a drawing or sample, material, quantity and destination. Here you will find how to prepare a quote, repeat an order and organise transport. Custom manufacturing starts from 4 units and is subject to technical review.

  1. Set of HARDVANES vanes fanned out with reference H100X45X4 engraved on the edge of each vane
    Set of HARDVANES vanes fanned out with reference H100X45X4 engraved on the edge of each vane

    Buy or order custom-made

    What technical difference does HARDVANES offer compared to the original spare?

    The choice must be based on the exact reference, material composition, geometry, surface finish and actual working conditions. HARDVANES offers compatible alternatives for the models indicated in each data sheet.

    In our EKVAC EVO+ carbon graphite vanes, the material comes from Germany and the machining, milling and polishing are carried out in Spain. We use material made specifically for vacuum and compression applications; graphite intended for electric motor brushes should not be considered equivalent on the basis of its appearance. Compatibility is verified for each reference, geometry and working condition.

    To buy a compatible vane, compare the spare part sheet with your vacuum pump documentation. A similar photograph or a matching measurement is no substitute for checking the material and the full reference.

  2. Four custom-made vanes next to a minimum order label of 4 units
    Four custom-made vanes next to a minimum order label of 4 units

    Buy or order custom-made

    Is there a minimum order?

    For custom manufacturing, the minimum order is 4 units. For catalog references, check the available quantity and supply conditions.

    Distinguish between individual units, complete sets and manufacturing batches: they do not always represent the same number of vanes. Indicate how many pumps you need to maintain and what each set includes so that the quote reflects your actual need.

  3. Black shipping box with gold HARDVANES logo, sealed, with destination label and fragile sticker
    Black shipping box with gold HARDVANES logo, sealed, with destination label and fragile sticker

    Buy or order custom-made

    Do you ship internationally?

    Yes. To prepare a transport offer, please indicate the country, city, postcode and quantity. We will confirm the service, cost and estimated delivery time.

    If you are buying from another country, please also provide your company's billing details and receiving instructions. Check the offer to see which items are included in the transport and who manages the procedures corresponding to the destination.

  4. Estimated lead time sheet with technical validation, manufacturing and transport phases next to the vane drawing
    Estimated lead time sheet with technical validation, manufacturing and transport phases next to the vane drawing

    Buy or order custom-made

    What is the lead time for custom manufacturing?

    It depends on the material, dimensions, geometry, requested volume and technical validation. After receiving the drawing or sample, we provide the estimated lead time in the offer.

    Separate the validation time for the part, manufacturing time and transport time. If you have a scheduled maintenance shutdown, communicate the required date before ordering to assess the schedule with all the information.

  5. Graphite sheet held in a vice under a carbide milling cutter, with graphite chips
    Graphite sheet held in a vice under a carbide milling cutter, with graphite chips

    Buy or order custom-made

    Where are HARDVANES vanes manufactured?

    HARDVANES relies on manufacturing and machining in Spain for its own-production references. The specific origin of each supply can be verified in its commercial documentation.

    In our own production vanes, machining determines dimensions, bevels and functional surfaces. To compare suppliers, request information on the quality of the material and the work performed on the part, in addition to the country of manufacture.

  6. Used vane as a sample, digital calliper, dimensioned drawing and photographs of the rotor to study the part
    Used vane as a sample, digital calliper, dimensioned drawing and photographs of the rotor to study the part

    Buy or order custom-made

    How long does a reverse engineering process take?

    The lead time is determined after examining the sample, its dimensions, and the equipment documentation. A damaged part may require additional verification.

    A used sample reflects both the original geometry and the accumulated wear. Accompany it with photographs of its position, available measurements, and equipment data; this allows design features to be distinguished from service damage.

  7. Service manual, technical data sheet, and a photograph of the pump's nameplate
    Service manual, technical data sheet, and a photograph of the pump's nameplate

    Buy or order custom-made

    What documentation do I need to provide?

    Brand, full model, serial number, previous reference, and a legible photograph of the nameplate. For custom manufacturing, add a dimensioned drawing, CAD file, or physical sample.

    Photograph the entire nameplate, not just the brand logo. Include model suffixes, manual references, and the number of vanes per set. This information reduces subsequent queries and helps prepare a more accurate offer for the replacement part.

  8. Open black HARDVANES box, with gold logo on the front and vanes secured upright in slotted foam
    Open black HARDVANES box, with gold logo on the front and vanes secured upright in slotted foam

    Buy or order custom-made

    How are parts protected during transport?

    The packaging must immobilise the vanes and protect their edges and machined surfaces. Inspect the parts upon receipt and report any possible damage immediately with photographs.

    Upon receiving the order, check the reference, quantity, and condition before taking it to the workshop. Keep the batch identification and set aside any damaged parts; installing them before documenting the damage makes it difficult to assess what happened during transport.

  9. Technical inquiry sheet with equipment, symptom, and replacement part, alongside a used vane and a photo of the rotor
    Technical inquiry sheet with equipment, symptom, and replacement part, alongside a used vane and a photo of the rotor

    Buy or order custom-made

    Do you provide technical support?

    We can help identify the correct replacement part based on the documentation. Assembly and repair operations must follow the manufacturer's manual and be carried out by qualified personnel.

    A technical inquiry is most useful when it describes the symptom, when it appeared, and what recently changed in the installation. Add the reference of the replacement part used: this helps guide identification without confusing a mechanical failure with an incorrect selection.

  10. Offer for a company with reference, quantity, and payment terms indicated on the offer itself
    Offer for a company with reference, quantity, and payment terms indicated on the offer itself

    Buy or order custom-made

    What payment methods do you offer to companies?

    Terms depend on the transaction and are indicated in the quotation. If you require a specific B2B arrangement, please consult us before confirming the order.

    To process a professional purchase, prepare the registered company name, fiscal address, contact details, and internal purchase reference. Review the conditions indicated in the offer before issuing your order; do not assume that all transactions have identical terms.

  11. Quote request with model, serial number, reference, quantity, and date, alongside the photo of the nameplate and the vane
    Quote request with model, serial number, reference, quantity, and date, alongside the photo of the nameplate and the vane

    Buy or order custom-made

    How do I request a quote?

    Send the brand, full model, serial number, previous reference, quantity, and photographs of the nameplate and the vane. With this data, we prepare the offer including material, lead time, and terms.

    Add the date you need the material and distinguish between a planned replacement and an urgent breakdown. If you attach measurements, indicate their unit and source. A complete request allows the replacement to be evaluated without relying solely on a commercial description.

  12. Sample vane in a sealed bag in front of HARDVANES black boxes from a large order
    Sample vane in a sealed bag in front of HARDVANES black boxes from a large order

    Buy or order custom-made

    Can I request a sample before a large order?

    Consult us before confirming the order. Sample availability depends on the reference, the material, and whether the part is a catalog item or a custom vane.

    Explain what you want to verify with the sample: dimensions, intended assembly, or reference identification. Agree on the scope of this verification beforehand; having a sample does not replace technical validation nor does it guarantee performance under all conditions.

  13. Workshop shelf with black HARDVANES vane boxes, with gold logo and equipment and size label
    Workshop shelf with black HARDVANES vane boxes, with gold logo and equipment and size label

    Buy or order custom-made

    Do you work with distributors and maintenance workshops?

    We can consider terms for industry professionals. Please indicate your activity, the projected volume, and the references you need.

    For recurring purchases, organise your references by pump brand and model, without grouping parts solely by size. A clear list of common replacement parts allows for supply planning and separates catalog references from custom manufacturing.

  14. Invoice for the company and material certificate for the supplied batch
    Invoice for the company and material certificate for the supplied batch

    Buy or order custom-made

    Do you issue invoices and commercial documentation for companies?

    Yes, the transaction is documented with an invoice. If your company requires additional documentation, please request it before confirming the order.

    Send the fiscal details and the administrative reference that must appear on the transaction. If you need certificates or material documentation, specify the requirement when requesting the offer; not all special documentation is automatically part of every supply.

  15. HARDVANES black box received with a vane that does not match the label, alongside the delivery note
    HARDVANES black box received with a vane that does not match the label, alongside the delivery note

    Buy or order custom-made

    What should I do if I receive a part different from the one ordered?

    Keep the original packaging and do not install the part. Write to us with the order number and photographs of the part and the label to review the case.

    Distinguish between an incorrect reference and an apparent difference in packaging or marking. Also attach the delivery note and the requested reference. The documentary review must be carried out before machining, sanding, or installing a part whose identity is not confirmed.

  16. Two identical batches of vanes on the revision B drawing from the previous order
    Two identical batches of vanes on the revision B drawing from the previous order

    Buy or order custom-made

    Can I repeat a custom order with the same specification?

    Yes, provided the drawing, sample, or agreed reference is kept. Indicate the previous order reference to avoid differences between batches.

    Include the drawing revision, not just the old order number. If the pump or application has changed, state this expressly; repeating a supply with the same geometry requires keeping the agreed technical specification identified.

  17. Drawing folder marked as confidential and non-disclosure agreement
    Drawing folder marked as confidential and non-disclosure agreement

    Buy or order custom-made

    How is the confidentiality of my drawings handled?

    We use the documentation solely to study and manufacture your part. If you require a formal non-disclosure agreement, please request it before sending the drawings.

    Before sharing files, check that you have authorisation to use that documentation and remove information unrelated to the part. Identify the drawing version and the technical contact so that queries are linked to a particular specification.

  18. Order packed in a black box with gold HARDVANES logo and collection in person label
    Order packed in a black box with gold HARDVANES logo and collection in person label

    Buy or order custom-made

    Can I collect the order in person?

    Please enquire when requesting the offer. Delivery options are confirmed according to the reference, quantity, and availability.

    Confirm the location, date, and the person authorised to collect the material before travelling. Collection depends on order preparation; a quote request or a technical inquiry does not mean the supply is ready.

Can't find your question? Send us your reference.

Indicate the pump or compressor model and the replacement part reference, and include a photo of the nameplate. State whether it runs dry or lubricated, the quantity, and the delivery country. For custom vanes, add length, height, and thickness, or a drawing.

Your opinion matters

Rate this page

00.20.40.60.81HARDVANESbar abs
Vacuum gauge100% of rated vacuum
00.511.522.5HARDVANESbar
Pressure gauge100% of rated pressure

HARDVANES

New vanes. Your pump, back to 100% performance.

Worn vanes give no warning: the pump keeps turning, but it no longer delivers 100%.

Worn vanes

It loses vacuum and pressure, and takes longer to do the same job.

New vanes

Factory vacuum and pressure are back: 100% performance.

Find your vanes With the cylinder, rotor and the rest of the pump in good condition.